Pulnix TMC-1000 Series Bedienungsanleitung Seite 3
- Seite / 12
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
External Sync
The TM-1400 accepts an external sync. of standard
HD and VD at TTL level for general locking to a system
sync. and clock. External sync. is available for 30-frame
mode only. The frequency requirement is as follows:
fHD = 31.09 KHz ±2%
fVD = 29.5 Hz ±2%
(Internal Master clock = 100.0 MHz,
Pixel clock = 25.0 or 50.0 MHz)
Please contact PULNiX for TM-1400 timing charts.
No-delay Shutter and Read-out-inhibit
For multiple-camera applications such as 2D or 3D
measurement and multi-angle inspection, simultaneous
image capturing at an exact shutter timing for all
cameras is a critical requirement. The TM-1400’s async
pulse width control mode provides no-delay shutter
as standard. Regardless of internal pulse timing, it
discharges at VINIT’s leading edge and transfers charges
at the trailing edge of the pulse. Even though each
camera runs with slightly different H and data clock
timing, image capturing is exactly simultaneous.
The TM-1400 also has read-out-inhibit control (ROI)
to control the vertical clock start (Async Shutter #9).
When ROI is low, V-clock is stopped and the transferred
charges remain in the vertical shift registers, which
works like CCD memory. When ROI is high, it clocks out
the CCD data. This helps a single frame grabber process
multiple images in pipeline processing (sequential
process).
Mode Switches
Various modes can be implemented with the rear
panel-mode selection switch and Up/Down switch as well
as RS-232 external control. When RS-
232 is connected, the command over-
writes the rear panel switch settings.
Connector and Pin Configurations
Digital Output Connector
Shutter Control Switch
Manual Async
0 no shutter no shutter
(1/15) (1/15)
1 1/60 1/16,000
2 1/125 1/8,000
3 1/250 1/4,000
4 1/500 1/2,000
5 1/1,000 1/1,000
6 1/2,000 1/500
7 1/4,000 1/250
8 1/8,000 1/125
9 1/16,000 Ext. pulse width
control
(For 30 fps mode, the shutter speed
doubles)
12-Pin Connector
1 GND (power) 7 VD in
2 +12V 8 GND
3 GND (analog) 9 HD in
4 Video out 10 RXD(RS232)
5 GND (digital) 11 INTEG/ROI
6 VINIT in 12 TXD(RS232)
Mode Switch Up/Down Switch Functions
0 Switch Disabled Switch Disabled None
1 Set Gain Up / Down Change gain
2 Set Vtop (A/D) Up / Down Change A/D ref. top
3 Set Vbottom (A/D) Up / Down Change A/D ref bottom
4 Gain Selection #1 Up: 9dB, Down: 12dB Lower gain selection
5 Gain Selection #2 Up: 18dB, Down: 22dB Higher gain selection
6 Linear LUT Up Back to linear table
7 Knee Selection Up / Down (Scroll) Scroll 8 different LUTs
8 Async Reset Mode Up: Normal, Dwn: Async Async and normal shutter
9 Factory Default Recall Up / Down: Recall Factory setting
A Power up Setting Up: Recall, Dwn: Save Power up page setting
B User Page Storage#1 Up: Recall, Dwn: Save User page storage setting
C User Page Storage#2 Up: Recall, Dwn: Save User page storage setting
D Direct Shutter Control Up / Down Shutter speed increment
by 1H
E Scan Format2 Up: 500, Dwn: 250 Partial selection
F Scan Format1 Up: 30 fps, Dwn: 15 fps Custom option scanning
VINIT (External Pulse Width Control Trigger)
No-Delay Shutter (All cameras)
No-delay Exposure
Discharge
Tr
ansfer Gate
ROI Control: Camera #1
Camera #1
Video
ROI Control: Camera #2
Camera #2
Video
Readout start pulse width: Min. 1H to 1frame
Max. 1H delay
FDV/Vsync
31-Pin Connector (MQ21-031-113-4300)
Pin# Description I/O Pin# Description I/O
1 CLK+ Out 17 CLK- Out
2 LDV+ Out 18 LDV- Out
3 FDV+ Out 19 FDV- Out
4 GND 20 VINIT (TTL) In
[INTEG (TTL) In]
5 EXT HD (TTL) In 21 EXT VD (TTL)
[EXT CLK+ In] [EXT CLK- In]
6 INTEG/ROI (TTL) In 22 N/C
[HD+ In] [HD- In]
7 N/C 23 GND
[Vinit+/(VD+) In] [Vinit-/(VD-) In]
8 D0+ Out 24 D0- Out
9 D1+ Out 25 D1- Out
10 D2+ Out 26 D2- Out
11 D3+ Out 27 D3- Out
12 D4+ Out 28 D4- Out
13 D5+ Out 29 D5- Out
14 D6+ Out 30 D6- Out
15 D7+ Out 31 D7- Out
16 GND
Note: CLK: data clock, LDV: Line data valid, FDV: Frame data valid, INTEG: Integration
control, EXT CLK: external pixel clock, [ ]: Differential input option
- AccuPiXEL Series 1
- Dynamic Range Control 2
- Scan Mode 2
- 3
- SPECIFICATIONS 4
- Graphical User Interface 4
- Serial Communication Kit 4
- Cameras 5
- 26 Position 6
- High Density 6
- Mini D Ribbon 6
- (MDR) Male Plug 6
- Camera Link Connector 7
- Color AccuPiXEL 9
- Starting Pixel Configuration 10
- Sync and Data 10
- Camera Functions 11
- Interpolation Software 11
- Color Interpolation 11
- Color AccuPiXEL Cameras 12
Verwandte Produkte und Handbücher für Sicherheitskameras Pulnix TMC-1000 Series
(70 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.110 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern