Pulnix TM-7EX Handbuch

Cognex MVS-8000 SeriesMVS-8100L Hardware ManualOctober 2006Email : 2 rue René Laennec 51500 Taissy France Fax: 03 26 85 19 08, Tel : 03 26 82 49 2

MVS-8100L Hardware Installation 110 Cognex MVS-8100L Hardware ManualCaution Electrostatic discharge (ESD) can damage the electronic components of your

1 MVS-8100L Hardware InstallationCognex MVS-8100L Hardware Manual 113. Select the source of +12 V camera power by positioning jumper JP1. Figure 2 sh

MVS-8100L Hardware Installation 112 Cognex MVS-8100L Hardware ManualNote Changing or adding cameras after installation with the board configured for i

1 MVS-8100L Hardware InstallationCognex MVS-8100L Hardware Manual 13 Figure 5. Location of pin 1 of connector JP3 on MVS-8100LCaution Failure to matc

MVS-8100L Hardware Installation 114 Cognex MVS-8100L Hardware Manual Figure 7. Location of pin 1 on connector JP4 of MVS-8100L Caution Failure to alig

1 MVS-8100L Hardware InstallationCognex MVS-8100L Hardware Manual 15The old and new JP2 connectors are are not meant to be interchangeable with the t

MVS-8100L Hardware Installation 116 Cognex MVS-8100L Hardware ManualConfiguring CamerasSome of the cameras supported for use with the MVS-8100L requir

1 MVS-8100L Hardware InstallationCognex MVS-8100L Hardware Manual 17Configuring Sony XC-ST50 CamerasThe MVS-8100L supports the use of the Sony XC-ST5

MVS-8100L Hardware Installation 118 Cognex MVS-8100L Hardware ManualConnecting External I/O EquipmentYou can connect the following external I/O equipm

1 MVS-8100L Hardware InstallationCognex MVS-8100L Hardware Manual 193. Connect a camera to the splitter cable as required.

The software described in this document is furnished under license, and may be used or copied only in accordance with the terms of such license and wi

MVS-8100L Hardware Installation 120 Cognex MVS-8100L Hardware Manual

Cognex MVS-8100L Hardware Manual 21MVS-8100L Hardware DescriptionThis chapter describes the hardware specifications for the Cognex MVS-8100L frame gra

MVS-8100L Hardware Description 222 Cognex MVS-8100L Hardware ManualMechanical SpecificationsThe Cognex MVS-8100L is 107 mm (4.2 inches) high by 175 mm

2 MVS-8100L Hardware DescriptionCognex MVS-8100L Hardware Manual 23Environmental RequirementsTable 4 lists the environmental requirements for the MVS

MVS-8100L Hardware Description 224 Cognex MVS-8100L Hardware ManualElectrical SpecificationsThis section describes the electrical specifications for t

2 MVS-8100L Hardware DescriptionCognex MVS-8100L Hardware Manual 25Output Power Indicator LEDsFour LEDs on the top edge of the MVS-8100L show the sta

MVS-8100L Hardware Description 226 Cognex MVS-8100L Hardware ManualCamera Port ConnectorsCamera 0 and 1 port connectors are high-density, 15-pin, HD-1

2 MVS-8100L Hardware DescriptionCognex MVS-8100L Hardware Manual 27Pinout of Camera Ports 0, 2, and 3The pinout of camera ports 0, 2, and 3 is simila

MVS-8100L Hardware Description 228 Cognex MVS-8100L Hardware ManualCamera Splitter Cable RJ-12 JackThe RJ-12 jack carries the I/O signals. Figure 14 s

2 MVS-8100L Hardware DescriptionCognex MVS-8100L Hardware Manual 29Camera Port Expansion PanelThe camera port expansion panel carries signals for cam

Cognex MVS-8100L Hardware Manual 3ContentsPreface ...

MVS-8100L Hardware Description 230 Cognex MVS-8100L Hardware Manual5 Ground (Camera) 6 No connect7 Analog ground 8 No connect9 +12 VDC (Camera 2 power

2 MVS-8100L Hardware DescriptionCognex MVS-8100L Hardware Manual 31Trigger and Strobe Expansion PanelThe trigger and strobe expansion panel, Cognex P

MVS-8100L Hardware Description 232 Cognex MVS-8100L Hardware ManualNote The PWR (pin 3) and GND (pin 5) connections on the DB-9F connector supply +5 V

2 MVS-8100L Hardware DescriptionCognex MVS-8100L Hardware Manual 33Jumper and Jack Settings for the MVS-8100LTable 12 lists the jumpers and jacks on

MVS-8100L Hardware Description 234 Cognex MVS-8100L Hardware ManualSchematics for I/O CircuitsThis section shows schematic circuit diagrams for the I/

2 MVS-8100L Hardware DescriptionCognex MVS-8100L Hardware Manual 35The schematic of the status output circuit is shown in Figure 21. Figure 21. Statu

MVS-8100L Hardware Description 236 Cognex MVS-8100L Hardware ManualStrobe OutputStrobe output is used to activate a photo strobe at the instant of ima

2 MVS-8100L Hardware DescriptionCognex MVS-8100L Hardware Manual 37MVS-8100L Cameras and Camera CablesYou may purchase cameras for use with the MVS-8

MVS-8100L Hardware Description 238 Cognex MVS-8100L Hardware Manual

Cognex MVS-8100L Hardware Manual 39IndexSymbols+12 V power 24, 26, 27, 29, 30, 33Numerics300-0155 37300-0175 14, 15300-0177 12300-0178 18, 27, 28300-0

4 Cognex MVS-8100L Hardware ManualIndex ...

Index40 Cognex MVS-8100L Hardware ManualMMVS-8100L+12 V power 24, 26, 27, 29, 30, 33configuring 11features 21Ppart number300-0155 37300-0175 14, 15300

Cognex MVS-8100L Hardware Manual 5PrefaceThis manual describes the Cognex MVS-8100L frame grabber and has the following sections:• MVS-8100L Hardware

6 Cognex MVS-8100L Hardware ManualStyle Conventions Used in This ManualThis manual uses the following style conventions:boldface Used for C/C++ keywo

Cognex MVS-8100L Hardware Manual 7Cognex OfficesCognex Corporation serves its customers from the following locations: Corporate Headquarters Cognex C

8 Cognex MVS-8100L Hardware Manual

Cognex MVS-8100L Hardware Manual 9MVS-8100L Hardware InstallationThis chapter describes how to install the Cognex MVS-8100L frame grabber in a host PC